Send Message
Paziņojums par privātumu: jūsu privātums mums ir ļoti svarīgs. Mūsu uzņēmums sola neatklāt jūsu personisko informāciju nevienai eksponācijai ar skaidrām atļaujām.
Mājas>
Produktu katalogs
Pdf is encrypted. Please provide your email address and enter your password to access
We provide PDF for you to look at the catalog, and you need to provide an email address.
Bezmaksas katalogi We provide PDF for you to look at the catalog, and you need to provide an email address.
-
1D Fuel Pump Catalog 15
The fuel pump is one of the basic components of the EFI vehicle fuel injection system, located inside the vehicle fuel tank, and the fuel pump works when the engine is started and running. If the engine is stopped while the ignition switch is still ON, the HFM-SFI control module turns off the power to the fuel pump to avoid accidental ignition.
-
1D Oil Pump Catalog 14
The role of the oil pump in the lubrication system: the role of the oil pump is to increase the oil to a certain pressure, forcing the ground pressure to the moving surface of the engine parts. The structure of oil pump can be divided into two categories: gear type and rotor type. Gear type oil pump is divided into internal gear type and external gear type, generally referred to as the latter gear type oil pump.
-
1D Crankshaft Catalog 13
The crankshaft is the most important part of an engine. It takes the force from the connecting rod and converts it into torque output through the crankshaft and drives the other accessories on the engine to work. The crankshaft is affected by centrifugal force of rotating mass, periodic gas inertia force and reciprocating inertia force, which makes the crankshaft bear the action of bending and torsional load. Therefore, the crankshaft is required to have sufficient strength and stiffness, and the journal surface should be wear-resistant, uniform and balanced.
-
1D Engine Valve Catalog 12
The role of the valve is specifically responsible for the input of air into the engine and exhaust the exhaust gas after combustion. From the engine structure, it is divided into intake valve and exhaust valve. The role of the intake valve is to draw air into the engine and mix it with the fuel to burn; The function of the exhaust valve is to discharge the exhaust gas after combustion and dissipate heat.
-
1D Ignition Coil Catalog 11
The core components of the ignition device are the ignition coil and the switching device, improve the energy of the ignition coil, the spark plug can produce enough energy spark, which is the basic condition of the ignition device to adapt to the operation of modern engines.
-
1D Head Gasket Catalog 10
The cylinder gasket is an elastic sealing element placed between the cylinder block and the cylinder head. Since it is impossible to be absolutely flat between the cylinder block and the head, the cylinder head liner is required to prevent high pressure gas, lubricating oil and cooling water from escaping between them.
-
1D Full Gasket Catalog 09
Full Gasket generally includes: front and rear crankshaft oil seal, oil pan pad, cylinder pad, valve chamber cover pad, intake and exhaust manifold pad, valve oil seal, pump pad camshaft oil seal, oil injection nozzle upper and lower oil ring, gasoline filter.
-
1D Engine Oil Catalog 08
Engine oil is the oil used to lubricate the moving components of the engine crankcase. Engine oil also has cooling and cleaning effects on the engine. Engine oil consists of base oil and additives. Base oil is mainly refined mineral oil, synthetic oil or a mixture of refined mineral oil and synthetic oil. Additives include antioxidant, viscosity index improver, coagulant, corrosion prevention agent, cleaning dispersant, friction improver, anti-wear agent and so on.
-
1D Glow Plug Catalog 07
Electric plug is also called preheating plug. During cold periods when the diesel engine is cooled, the electric plug provides heat to improve the starting performance. At the same time, the electric plug is required to have the characteristics of rapid heating and permanent high temperature state.
-
1D Spark Plug Catalog 06
Spark plug is an important component of gasoline engine ignition system, it can introduce high voltage into the combustion chamber, and make it skip electrode gap and spark, so as to ignite the combustible mixture in the cylinder. It is mainly composed of a wiring nut, an insulator, a wiring screw, a center electrode, a side electrode and a shell, and the side electrode is welded on the shell.
-
1D Engine Bearing Catalog 05
The bearing bush is the part of the plain bearing and the journal in contact, the shape of a tile-like semi-cylindrical surface, very smooth. The bearing material is characterized by small friction coefficient, sufficient fatigue strength, good running performance and good corrosion resistance. Commonly used bearing materials are bearing alloy (Babbitt), copper alloy, powder metallurgy and gray cast iron and wear-resistant cast iron.
-
1D Cylinder Liner Catalog 04
The cylinder liner is a cylindrical part that is placed in the cylinder block hole of the body and is secured by the cylinder head. The piston reciprocates in its inner hole and is cooled by cooling water outside.
Mēs ar jums sazināsimies tūlīt
Aizpildiet vairāk informācijas, lai varētu sazināties ar jums ātrāk
Paziņojums par privātumu: jūsu privātums mums ir ļoti svarīgs. Mūsu uzņēmums sola neatklāt jūsu personisko informāciju nevienai eksponācijai ar skaidrām atļaujām.